Home› General Discussion

Spots on my Heartfelt Beads

nsezellnsezell Everyone, Registered Users Posts: 294
in General Discussion
A couple days ago I found a few black spots in my mesh bag with my beads in it. I've read a couple threads and it looks like it may be mold. Assuming it is mold, I have enough back up beads to replace these with, but I hate to throw them away if they're fixable. I was considering soaking them in either isopropyl alcohol, or a bleach solution, but I wasn't sure if it would screw up the properties of the beads. Anyone have any thoughts on what it might do or what else I should do to clean the beads? Again, I can throw them out if it doesn't work, but I'd rather have more rebound ability with more beads. Thanks. -nsezell
· Share on FacebookShare on Twitter

Comments

  • laker1963laker1963 Everyone, Registered Users Posts: 5,046
    nsezell:
    A couple days ago I found a few black spots in my mesh bag with my beads in it. I've read a couple threads and it looks like it may be mold. Assuming it is mold, I have enough back up beads to replace these with, but I hate to throw them away if they're fixable. I was considering soaking them in either isopropyl alcohol, or a bleach solution, but I wasn't sure if it would screw up the properties of the beads. Anyone have any thoughts on what it might do or what else I should do to clean the beads? Again, I can throw them out if it doesn't work, but I'd rather have more rebound ability with more beads. Thanks. -nsezell
    Not sure about how to clean them beads. I would worry about them too much and just toss them if they were mine.

    This situation raises a question. Did you use Distilled water on these beads? Distilled water should NOT mold like that. If not then when you charge the new beads make sure that you use only distilled water. No PG solutions, or tap water as the contaminants can cause mold to grow.
    · Share on FacebookShare on Twitter
  • jihiggsjihiggs Everyone, Registered Users Posts: 468
    I dont think there is anyway to clean them with any certainty. if you dont get all the mold you will just have another break out.
    · Share on FacebookShare on Twitter
  • The SniperThe Sniper Everyone, Registered Users Posts: 3,910
    nsezell:
    A couple days ago I found a few black spots in my mesh bag with my beads in it. I've read a couple threads and it looks like it may be mold. Assuming it is mold, I have enough back up beads to replace these with, but I hate to throw them away if they're fixable. I was considering soaking them in either isopropyl alcohol, or a bleach solution, but I wasn't sure if it would screw up the properties of the beads. Anyone have any thoughts on what it might do or what else I should do to clean the beads? Again, I can throw them out if it doesn't work, but I'd rather have more rebound ability with more beads. Thanks. -nsezell
    OMG this is SO freaking bizzare!!! I swear to God, I came on here tonight to post that I had found the exact same thing! Mine were in my coolidor, and I think in my case that I just left too much water on the mesh bag when I put it back in there on the spanish cedar. Went ahead and just tossed my beads along with the spanish cedar panel they were sitting on, as I couldnt take the chance with my babies! Inspected the cigars in there thoroughly & all seems well.

    Just super duper freaky that this happened to two of us today, when I had never seen any mention of it in the forums!

    · Share on FacebookShare on Twitter
  • KriegKrieg Everyone, Registered Users Posts: 5,068
    The Sniper:
    nsezell:
    A couple days ago I found a few black spots in my mesh bag with my beads in it. I've read a couple threads and it looks like it may be mold. Assuming it is mold, I have enough back up beads to replace these with, but I hate to throw them away if they're fixable. I was considering soaking them in either isopropyl alcohol, or a bleach solution, but I wasn't sure if it would screw up the properties of the beads. Anyone have any thoughts on what it might do or what else I should do to clean the beads? Again, I can throw them out if it doesn't work, but I'd rather have more rebound ability with more beads. Thanks. -nsezell
    OMG this is SO freaking bizzare!!! I swear to God, I came on here tonight to post that I had found the exact same thing! Mine were in my coolidor, and I think in my case that I just left too much water on the mesh bag when I put it back in there on the spanish cedar. Went ahead and just tossed my beads along with the spanish cedar panel they were sitting on, as I couldnt take the chance with my babies! Inspected the cigars in there thoroughly & all seems well.

    Just super duper freaky that this happened to two of us today, when I had never seen any mention of it in the forums!

    wow...now im paranoid...gotta go check my beads
    · Share on FacebookShare on Twitter
  • cabinetmakercabinetmaker Everyone, Registered Users Posts: 2,561
    I keep air moving, never had mold issues. Laker's right, toss the beads.
    · Share on FacebookShare on Twitter
Sign In or Register to comment.