How Do You Cut Your Cigar

scooter mcgee

So far I only use the double guillotine, but I was curious to how the rest of you might use other types of cutters on different types of cigars

Poopy Jones

Punch cutter mostly. For torpedoes and such I have a nice guillotine cutter

Cigary

There are different ways to cut your cigar and it's what you like that becomes your favorite way. Try as many as you can to see the differences....V CUT---Punch Cut--Dickman Cut--Double V Cut--Scissor Cut

jgibv

Vividone

For me it depends on the gague of the cigar. 50 and below guillotine anything above I use a punch.

Gino USMC

Double guillotine always.

jliu

with mah teeth yo

Martel

Gray4lines

Usually xikar double guillotine , but more recently have been using a punch more. Sometimes will cut a torpedo at an angle to get more of a draw.

CigarManNo1

I also prefer double guillotine and for me it depends on cigars also, as I usually smoke 3 different ones, I cut each one differently, sometimes according to mood. Does someone cut only one way also, like a habit or something?

scooter mcgee

What is the Dickman cut? Possibly a picture?

kingdavid5

I use the Cuban crafters perfect cutter for all sizes but I think I'm going to invest in a good v-cutter and I've actually never tried to punch a stick yet

Martel

scooter mcgee:

What is the Dickman cut? Possibly a picture?

It's basically a straight cut but made at a 45 degree angle. The intention is to direct the smoke toward the palate or some such. I see it kind of like the attempt to punch through a chisel tip, which works okay, but is not much of a difference to me from a squeeze or a straight cut on those cigars.

SleevePlz

A simple cut with my Xikar every time, unless it is an LFD chisel which doesn't need a cut. I'm not sure if I've mentioned this before, but I really like LFD's, especially the chisels. So convenient and tasty, but I digress

jadelt

Martel:

scooter mcgee:

What is the Dickman cut? Possibly a picture?

It's basically a straight cut but made at a 45 degree angle. The intention is to direct the smoke toward the palate or some such. I see it kind of like the attempt to punch through a chisel tip, which works okay, but is not much of a difference to me from a squeeze or a straight cut on those cigars.

Whewww !!! I was afraid it had something to do with circumcision or something painful

jd50ae

When I started smoking cigars I used a very special knife and made a Churchill V. Progressed to a bullet punch which I kept on my key-chain. I just bought a Cuban Crafters 3 blade scissor type which I will use at home when the bullet punch does not supply enough draw. I have not smoked a torpedo so that does not enter into the mix (yet).

New Boots

jliu

This morning, with my teeth. Who saved money? Jiunn

11rocket11

I use my Xikar Xi cutter, if I forget that I use a punch. Just out of curiosity, has anybody used a Shuriken? If so what do you think?

90+ Irishman

Xikar 009 punch is my go to whenever I have the choice otherwise I use my Xikar guillotine cutter

bigharpoon

I use my Xikar scissors almost all the time. When I don't have it I usually use my fingernail. My other cutters are basically just clutter at this point, or for camping trips.

dr_frankenstein56

90+ Irishman

christian1971

I use my fingernail.

firetruckguy

95% of the time I use my V cutter, the other is a strait cut on a torp.......

Bob Luken

Usually a straight cut with a Xikar Xi2. Sometimes a punch. One day I'll try a v-cut.

rsherman24

I usually use a punch cut. If for some reason I get a tough draw, I will go to the cutter

brianetz1

xikar straight cut 99% of the time.

PAtoNH

V-cut up to about Toro size, punch on the Big ole Gordo/60 gauge gars, guillotine on torpedoes.

webmost

dr_frankenstein56